Advanced Search
Search Results
154 total results found
AET—F405 Wiring Diagram
AET-H743_basic-v2.0 Version
AET-4G Module User Guide
AET-H743AIR PRO User Manual
Chapter 4: Full Parameter List
Most additional settings are configured individually in the "Full Parameter List", which is one of the defining features of ArduPilot firmware. If "Full Parameter List" is not visible in Mission Planner, open the "Config/Tuning" page, select "Planner", set "L...
Chapter 5: Adjusting the OSD Layout
Open the OSD settings: CONFIG/TUNING -- Onboard OSD -- Screen1 ArduPilot OSD configuration is similar to INAV configuration and tuning because the flight controller includes an onboard OSD module. In the OSD item list at the bottom, enable the items to displa...
Chapter 6: ESC Throttle Range Calibration
After assembly, calibrate the ESC throttle range while the ESC is connected to the flight controller. Remove all propellers before calibration and ensure that the motors cannot contact surrounding objects. Procedure: Connect the flight controller to the comput...
Chapter 7: Onboard Bluetooth Telemetry Connection
The AeroEgg AET H743 Basic flight controller includes an onboard Bluetooth telemetry module. You can pair the flight controller with the Bluetooth adapter in a laptop computer. After pairing, the flight controller can connect to the computer ground station thr...
Chapter 8: RSSI Setup
Common receivers include ELRS, TBS_CRSF, and SIYI receivers. SBUS receivers do not provide RSSI. RSSI is represented through a PWM channel. ELRS receivers use CH15 to output simulated LQ signal quality, TBS CRSF receivers use CH12, and SIYI receivers use CH16....
Chapter 9: Connecting, Configuring, and Using the Airspeed Sensor
This example uses a Fapple airspeed sensor with the MS4525D protocol. Recommended wiring: use the 5V, GND, SCL, and SDA pins on the side uart4 connector. Install the airspeed sensor on the airframe according to its installation instructions, minimizing the ef...
Chapter 10: Adjusting Cruise Throttle
Users have reported that after the aircraft returns overhead during RTL, it may enter a high-speed orbit with 100% throttle output. We therefore recommend adjusting the following settings on the MP Basic Tuning page. CONFIG/TUNING --- Basic Tuning --- Throttle...
Chapter 11: WS2812 Programmable LED Strip Connection and Configuration
Connect the WS2812 LED strip using three wires: GND, 4~7V, and IN. Terminate them in a 2.54 mm 3-pin Dupont connector and plug it directly into a PWM servo output. Eight illuminated LEDs consume approximately 100mw, which places a relatively small load on the ...
Hardware Configuration
Detailed Hardware Specifications
Peripheral Connection Reference Diagrams
These diagrams are for reference only and apply only to ArduPilot firmware. Make all connections according to the actual hardware configuration. Main controller board: Power board:
Power Supply Logic
Warning: Never exceed the rated power capacity. Abnormal overheating in flight may damage the flight controller and cause a crash.
Pin Mapping Overview
ArduPilot Pin Mapping INAV Pin Mapping
Reference Materials and Appendices
Step-by-step AP firmware flight controller configuration tutorial (compiled by Piaopiao) https://doc.aeroeggtech.com/en/books/aet-h743-basic-ardupolit INAV firmware user guide: https://doc.aeroeggtech.com/en/books/aet-h743-basic-inav/page/aet-h743-basic-inav ...
Chapter 1: Flashing Flight Controller Firmware
The AeroEgg Technology AET F405A WING flight controller currently supports ArduPilot and INAV firmware. This guide focuses on fixed-wing configuration and tuning with ArduPilot firmware. You can upgrade the flight controller by flashing the latest firmware. Do...
Chapter 2: Flight Controller Wiring
The wiring diagram for the AeroEgg AET F405A WING flight controller is shown below: Warning: The capacitor must be connected. Operating without it may damage the flight controller. Common peripherals include GPS modules, SBUS receivers, ELRS receivers/TBS CRS...
Chapter 3: Basic Configuration and Tuning - Six-Position Calibration, Compass, Servo, and Motor Setup
Section 1: Connect the Ground Station and Reset Default Parameters. Open the MissionPlanner configuration and tuning software. If the live satellite map does not load, open the ground station “Flight Plan” page and select the map source on the right. “Amap Sa...
Chapter 4: Receiver, GPS, Video Link, Bluetooth, and Telemetry Configuration
Receiver configuration: When using an SBUS receiver (such as Tiandifei WBUS, RadioLink, or Futaba series receivers), connect it directly to the flight controller SBUS port with a 2.54 mm 3-pin Dupont connector. The SBUS port corresponds to SERIAL PORT2 (UART2)...
Chapter 5: Radio Transmitter Calibration
If the radio transmitter is powered on and correctly bound to the receiver, but the receiver wiring to the flight controller or the corresponding serial-port configuration is incorrect, the radio calibration page will not display the Thrttle signal or channel ...
Chapter 6: Flight Controller Orientation and Attitude Display Check
The attitude indicator in ArduPilot firmware represents the pilot's first-person view from inside the cockpit, not an external third-person view. The blue upper area represents the sky, the green lower area represents the ground, and the boundary between them ...
Chapter 7: Flight Mode Configuration
ArduPilot uses one proportional channel to select among six flight modes. Channel 8 is used by default. The figure below shows the default ranges for the mode-selection channel. Use the drop-down arrow beside each flight mode position to select the required f...