Search Results

Q: Why is the compass not detected when the GPS and compass are connected to the side UART4 port? A: INAV firmware requires the compass to be connected to a designated I2C bus. To provide the best compatibility with different GPS modules, the AeroEgg H743 flig...

Introduction: This article explains only how to flash arbitrary firmware through DFU. Upgrade procedures specific to certain firmware, such as updating ArduPilot through the bootloader, are outside its scope. DFU is boot code permanently embedded in the flight...

Product Overview This product is a general-purpose GNSS and compass module compatible with most mainstream flight controllers and open-source firmware. Designed as an alternative to the BZ-251 series GNSS modules, it can acquire more than 30 satellites in appr...

INAV 8.0 Configurator download https://github.com/iNavFlight/inav-configurator/releases/tag/8.0.0 Firmware download https://github.com/iNavFlight/inav/releases AeroEgg Technology mirror (use this if GitHub downloads are unavailable) https://download.aeroeggtec...

Q: Why does the flight controller fail to detect my GPS when it is connected to UART4? A: Ensure that all serial ports below UART4 are not configured for the GPS protocol (for example, UART2), and that UART4 is configured for the GPS protocol. AP firmware sear...

When connecting the flight controller to a computer for the first time, disconnect all external devices so the flight controller is in an isolated test setup. Open Device Manager. If the flight controller is listed outside the Ports section, reinstall the driv...

Initial Flight Setup After Installing the Airspeed Sensor 1.ARSPD_TYPE = 1 (Other parameters become visible only after saving the change and reconnecting) 2.ARSPD_OPTIONS = 15 (select DisableVoltageCorrection) 3.ARSPD_AUTOCAL = 1 4.ARSPD_SKIP_CAL = 1 After cha...

Download link for INAV firmware, ArduPilot firmware, and ground station software: https://download.aeroeggtech.com/ How to install multiple versions of the INAV ground station software on the same computer: 1. When downloading the ground station software, sele...

The AET H743 flight controller includes an onboard Bluetooth telemetry module connected to the UART7 serial port through board headers. After configuring the corresponding serial-port parameters, you can connect the computer to the flight controller over Bluet...

AM32 ESC setup procedure: ① Complete the solder connections between the ESC and motor. ② Complete the solder connections between the ESC and flight controller. A capacitor must be installed at the ESC. ③ Solder the PWM wire and connect it to a motor output on ...

TODO

Flight Controller Board - Front Flight Controller Board - Rear ESC Board

Configure the analog camera power supply according to the actual camera requirements. An analog camera can use 5V or 9V; cameras rated below 5W may also use 9Vsw. Connect the primary video signal to CAM1. This flight controller supports two cameras, so connect...

My findings regarding the Betaflight OSD issue on the CH4 flight controller are as follows: To enable the OSD chip, enter the following commands in the CLI: set osd_displayport_device = MAX7456 save On the Modes page, USER2 switches the camera. It can be assi...

ArduPilot firmware is available at https://download.aeroeggtech.com/?dir=ArduPilot%E5%9B%BA%E4%BB%B6/AET-H743-CH4 BetaFlight firmware is available at https://download.aeroeggtech.com/?dir=BetaFlight%E5%9B%BA%E4%BB%B6/AET-H743-CH4

1: When the air unit is connected directly, pair the air unit's built-in SBUS receiver with the DJI FPV 2 radio transmitter. UART2 (corresponding to Serial2) is used as the SBUS port. In the port settings, configure Serial2 as follows: Baud rate Speed 57600 Pr...

Chapter 1: Flight Controller Firmware Flashing The AeroEgg AET H743 Basic flight controller currently supports ArduPilot and INAV firmware. This guide focuses on configuration and tuning for fixed-wing aircraft running ArduPilot. Firmware flashing can be used ...

The wiring diagram for the AeroEgg Technology AET H743 Basic flight controller is shown below: Common peripherals include GPS modules, SBUS receivers, ELRS receivers/TBS CRSF receivers, digital video air units (including DJI O3, O4, and Vista; Caddx Avatar se...

Section 1: Connect the Ground Station and Reset Default Parameters. Open the MissionPlanner configuration and tuning software. If the live satellite map cannot be loaded, open the Flight Plan page in the ground station and select a map source on the right. AM...