Search Results

When connecting the flight controller to a computer for the first time, disconnect all external devices so the flight controller is in an isolated test setup. Open Device Manager. If the flight controller is listed outside the Ports section, reinstall the driv...

Initial Flight Setup After Installing the Airspeed Sensor 1.ARSPD_TYPE = 1 (Other parameters become visible only after saving the change and reconnecting) 2.ARSPD_OPTIONS = 15 (select DisableVoltageCorrection) 3.ARSPD_AUTOCAL = 1 4.ARSPD_SKIP_CAL = 1 After cha...

Download link for INAV firmware, ArduPilot firmware, and ground station software: https://download.aeroeggtech.com/ How to install multiple versions of the INAV ground station software on the same computer: 1. When downloading the ground station software, sele...

The AET H743 flight controller includes an onboard Bluetooth telemetry module connected to the UART7 serial port through board headers. After configuring the corresponding serial-port parameters, you can connect the computer to the flight controller over Bluet...

AM32 ESC setup procedure: ① Complete the solder connections between the ESC and motor. ② Complete the solder connections between the ESC and flight controller. A capacitor must be installed at the ESC. ③ Solder the PWM wire and connect it to a motor output on ...

Configure the analog camera power supply according to the actual camera requirements. An analog camera can use 5V or 9V; cameras rated below 5W may also use 9Vsw. Connect the primary video signal to CAM1. This flight controller supports two cameras, so connect...

My findings regarding the Betaflight OSD issue on the CH4 flight controller are as follows: To enable the OSD chip, enter the following commands in the CLI: set osd_displayport_device = MAX7456 save On the Modes page, USER2 switches the camera. It can be assi...

1: When the air unit is connected directly, pair the air unit's built-in SBUS receiver with the DJI FPV 2 radio transmitter. UART2 (corresponding to Serial2) is used as the SBUS port. In the port settings, configure Serial2 as follows: Baud rate Speed 57600 Pr...

Chapter 1: Flight Controller Firmware Flashing The AeroEgg AET H743 Basic flight controller currently supports ArduPilot and INAV firmware. This guide focuses on configuration and tuning for fixed-wing aircraft running ArduPilot. Firmware flashing can be used ...

The wiring diagram for the AeroEgg Technology AET H743 Basic flight controller is shown below: Common peripherals include GPS modules, SBUS receivers, ELRS receivers/TBS CRSF receivers, digital video air units (including DJI O3, O4, and Vista; Caddx Avatar se...

Section 1: Connect the Ground Station and Reset Default Parameters. Open the MissionPlanner configuration and tuning software. If the live satellite map cannot be loaded, open the Flight Plan page in the ground station and select a map source on the right. AM...

Most additional settings are configured individually in the "Full Parameter List", which is one of the defining features of ArduPilot firmware. If "Full Parameter List" is not visible in Mission Planner, open the "Config/Tuning" page, select "Planner", set "L...

Open the OSD settings: CONFIG/TUNING -- Onboard OSD -- Screen1 ArduPilot OSD configuration is similar to INAV configuration and tuning because the flight controller includes an onboard OSD module. In the OSD item list at the bottom, enable the items to displa...

After assembly, calibrate the ESC throttle range while the ESC is connected to the flight controller. Remove all propellers before calibration and ensure that the motors cannot contact surrounding objects. Procedure: Connect the flight controller to the comput...

The AeroEgg AET H743 Basic flight controller includes an onboard Bluetooth telemetry module. You can pair the flight controller with the Bluetooth adapter in a laptop computer. After pairing, the flight controller can connect to the computer ground station thr...

Common receivers include ELRS, TBS_CRSF, and SIYI receivers. SBUS receivers do not provide RSSI. RSSI is represented through a PWM channel. ELRS receivers use CH15 to output simulated LQ signal quality, TBS CRSF receivers use CH12, and SIYI receivers use CH16....

This example uses a Fapple airspeed sensor with the MS4525D protocol. Recommended wiring: use the 5V, GND, SCL, and SDA pins on the side uart4 connector. Install the airspeed sensor on the airframe according to its installation instructions, minimizing the ef...

Users have reported that after the aircraft returns overhead during RTL, it may enter a high-speed orbit with 100% throttle output. We therefore recommend adjusting the following settings on the MP Basic Tuning page. CONFIG/TUNING --- Basic Tuning --- Throttle...

Connect the WS2812 LED strip using three wires: GND, 4~7V, and IN. Terminate them in a 2.54 mm 3-pin Dupont connector and plug it directly into a PWM servo output. Eight illuminated LEDs consume approximately 100mw, which places a relatively small load on the ...

Detailed Hardware Specifications