Search Results

2.1. AeroEgg AET H743 Basic Flight Controller Wiring Diagram Note the forward orientation of the flight controller. During accelerometer calibration in ArduPilot firmware, the aircraft must be positioned on its left side, right side, and in the other requeste...

2.1. Section 1: Ground Station Connection and Resetting Default Parameters Download the AGC configuration and tuning software from https://download.aeroeggtech.com/. Do not connect a battery to the flight controller. Connect the flight controller to the USB ex...

Ardupilot firmware allows the flight controller S1~S12 outputs to be fully customized. In the figure above, #1 corresponds to flight controller output S1, #2 corresponds to S2, and so on. Each output channel can be assigned from its corresponding drop-down me...

U7 Flight Controller AGC Configuration and Tuning Guide 1. Confirm the Aircraft Type 2. Flash the Firmware 3. Peripheral Wiring and Configuration 4. Basic Flight Controller Configuration and Tuning 5. Flight Mode Configuration 6. Detailed Parameters for Each F...

Flight Controller Calibration — Radio Calibration — Start Calibration Calibration Procedure If the receiver is wired correctly and the corresponding serial port is configured correctly, all channels will be visible and will respond when the radio transmitter...

Ardupilot uses one proportional channel to select among six flight modes. The default is radio transmitter channel 8; refer to the relevant settings if a different channel is required. Use the drop-down arrow to the right of each flight-mode position to select...

Most additional parameters are configured individually in the Full Parameter List. This level of detailed control is a key feature of ArduPilot firmware. When using the Full Parameter List, keep the configuration reference TXT file open on the computer for co...

Open the OSD information settings. AGC OSD display configuration is similar to INAV configuration and tuning (the OSD module is integrated into the flight controller). In the OSD content section at the bottom, select the items to display and drag them to the d...

Power the flight controller from the battery before using onboard Bluetooth. The AeroEgg Technology AET H743 Basic flight controller includes an onboard Bluetooth telemetry module. You can pair it with a laptop Bluetooth adapter and connect the flight controll...

Commonly used receivers include ELRS, TBS_CRSF, and SIYI receivers. SBUS receivers do not provide RSSI. These receivers use a PWM channel to represent the RSSI signal. ELRS receivers use CH15 to output the simulated LQ signal quality, TBS CRSF receivers use CH...

This example uses a Fapple airspeed sensor with the MS4525D protocol. Refer to the airspeed sensor installation instructions for mounting on the airframe, and minimize the effect of airframe turbulence on the sensor. Connect the airspeed sensor 5V and GND pins...

Procedure for configuring the AeroEgg H743 9VSW 9V video power switch 1. Configure the relay function ◦ Parameter: RELAY1_FUNCTION ◦ Value: 1 ◦ Function: Enables relay output 1 2. Assign the relay pin ◦ Parameter: RELAY_PIN ◦ Value: 81 ◦ Function: Selects th...

U7 Flight Controller AGC Configuration and Tuning Guide I. Identify the Airframe Type II. Flash the Firmware III. Peripheral Wiring and Configuration IV. Basic Flight Controller Configuration and Tuning V. Flight Mode Setup VI. Detailed Parameters for Each Fli...

Thank you for being with us throughout the journey. AeroEgg Technology is always here for you. We appreciate your trust and remain committed to your choice. We will continue serving every customer with care. We are honored by your recognition and fortunate to ...

The AeroEgg AET F405A WING flight controller currently supports ArduPilot and INAV firmware. This guide focuses on fixed-wing configuration and tuning with ArduPilot firmware. The flight controller can be upgraded to the latest firmware by flashing a firmware ...

The AeroEgg AET F405A WING flight controller wiring diagram is shown below: Common peripherals include GPS positioning modules, SBUS receivers, ELRS receivers/TBS CRSF receivers, digital air units (including DJI O3, O4, and Vista; Caddx Avatar series; and open...

Section 1: Connect the Ground Station and Reset Default Parameters. Open the AGC configuration and tuning software. Connect the flight controller to the computer with a Type-C data cable. In the upper-right corner of AGC, select the port assigned to the fligh...

When using the Full Parameter List, keep the configuration and tuning reference TXT file open on the computer. Copy a parameter name from the reference file and paste it into the Search box on the right side of the Full Parameter List. The page automatically ...

Open the OSD information settings: